Search this forum:
Search
Please register and login to participate in the forums.
Page 1 of 212 > >>
Topics
 Replies
 Views
 Last Post
3 Replies and 742 Views Is Anyone using a home energy monitoring system?  742  3 Started by  Joe Clark Hello, I am doing a fairly large project with all new hvac as well as building a home theater and my energy consumption has always been through the roof. I average 2,000 KWH a month already and my new additions may cause it to increase. I had an electrician laying out wires tell me I have some type of electrical problem, because 2,000 KWH is way too much for what I am using. He said I should install an electrical monitoring system to figure out where the power is going. I have see a bunch ...
3 742
by  Cale KeeJump to last post
05/15/2018 12:52 PM
0 Replies and 1205 Views Circuit for Measuring RMS Current Value using CR3110  1205  0 Started by  Daniel Blair I am currently using the precision rectifier circuit found in the 'Precision Rectifier Circuit for CT Signal Conditioning' app note. I am using this in my application to monitor motor current using a CR3110-3000 current transformer across a 7.5 ohm burden resistor. I now need to monitor current to non-linear loads (e.g., from a VFD) and hence need to get a true RMS value. Is there a similar circuit recommendation for non linear applications that allows me to still use the same CT
0 1205
06/02/2015 3:23 PM
1 Replies and 1597 Views Output isolation from input  1597  1 Started by  Viktor Sokolov Hello, from your manual for CR5200 and CR5300: ' Output isolated from input' -Is it galvanic isolation Thank you.
1 1597
by  Tony HodgesJump to last post
10/13/2014 11:08 AM
1 Replies and 1483 Views Repeatability of CR5200 and CR5300  1483  1 Started by  Viktor Sokolov Hello, what are the repeatability of measurements for CR5200 and CR5300
1 1483
by  Tony HodgesJump to last post
09/23/2014 9:12 AM
1 Replies and 1549 Views Current transducer CR5220  1549  1 Started by  Viktor Sokolov I like to install 2 CR5220 -(up to 30ADC first and up to 10ADC second)- on one DIN rail. Is there has to be some recommended distance between transducers to avoid any interference Thank you.
1 1549
by  Tony HodgesJump to last post
07/31/2014 9:05 AM
1 Replies and 1614 Views Measuring AC Voltage with CR4850-500  1614  1 Started by  Kristin Chew Hi, I would like to ask more advise on how to verify the output of the Voltage Transducer CR4850-500 The datasheet stated that the DC output is proportional to the AC voltage input. My question is: 1. The output from pin 7-9 (L1-N, L2-N, L3-N) is in DC or AC 2. The output value is giving out 0-5 VDC after measuring the input VAC So, for example if my max voltage is 240 VAC, the transducer will output 5VDC Is there any graph showing the linearity of the input and output voltages ...
1 1614
by  Tony HodgesJump to last post
06/30/2014 10:31 AM
2 Replies and 2024 Views DC Current Direction Through CT  2024  2 Started by  Joseph Hafich Building a few panels using your CR5220 to measure DC current from a battery charger to the battery positive terminal, and then output a 4-20 ma reference for metering. I could power up and test to determine, but thought I might ask. Wire from the battery charger through () on the window then to the battery Current will generally flow from the charger to the battery (hopefully). Thanks
2 2024
by  Joseph HafichJump to last post
05/15/2014 6:59 PM
1 Replies and 1547 Views DC Immune  1547  1 Started by  Randy Smith I've got a DC load design that I'm adding an AC voltage to. The AC doesn't cross zero so I have to add a DC offset. I need to measure total current and the CT I'm using just isn't delivering the correct AC value. I'm convinced the DC component of the signal is skewing the RMS value somehow. I see that CR makes CTs that are DC immune which is exactly what I need. Question is, in a nutshell how does that work Does the CT simply ignore the DC component somehow Thank you, Randy
1 1547
by  Tony HodgesJump to last post
05/02/2014 1:32 PM
1 Replies and 2210 Views measure of differential current  2210  1 Started by  martino bonacossa Hello, I have a question I'd like to submit. I'm trying to achieve a measure of differential current. I'm using a CR8348-2000 in which I inserted into the hole in both phases (phase and neutral). As the load resistance across the CR will use a 90.9k, then enter a LTC1967 and from there into a PIC. The scheme is in fact the one in the LTC1967 data sheet (http://cds.linear.com/docs/en/datasheet/1967f.pdf) on page 26. The problem is the response time. thanks for your cooperation and sorry for ...
1 2210
by  Tony HodgesJump to last post
12/27/2013 8:07 AM
1 Replies and 2391 Views AC current monitoring  2391  1 Started by  Vipin Kapoor hi! In one of our application; We want to monitor the AC current of already installed device & would like to transmit this AC current data via RS 232 interface for DATA logging purpose. Current range would be 0~40AAC, 50hz. Can you pls. suggest any cost effective solution
1 2391
by  Tony HodgesJump to last post
09/05/2013 11:24 AM
1 Replies and 2203 Views CR5210-50  2203  1 Started by  Robert Batta Hi, I have a CR5210-50 that I am using to measure DC load on a 12v distribution panel. I've wired the CT as drawn in the instruction, supplied 24vdc power, but the readings I am getting do not match the measured load: The amp readings below were taken is a separate amp meter and compared it to the voltage output on the CT: 2.86A - 2.35volts 9.9A - 2.08volts 11.4A - 201volts 12.9A - 1.96volts 13.8A - 1.03volts I feel like I'm missing something obvious.
1 2203
by  Tony HodgesJump to last post
08/26/2013 9:20 AM
1 Replies and 2324 Views Isolated AC Voltage and current Measurement  2324  1 Started by  David Wilson I am looking for a good way to create an isolated voltage and current measurement signal conditioner for a 120Vac 60Hz, 20A test. The inputs to my data acquisition system are /-10V. I need to measure voltage with 1/2 accuracy, current (2-3 accuracy is acceptable), total harmonic distortion, power factor, etc. Are there some recommended transformers for this application
1 2324
by  Tony HodgesJump to last post
08/13/2013 10:15 AM
1 Replies and 2279 Views Hi-Freq Lamp Ballast Current Monitoring  2279  1 Started by  Basel Z Hello, I have an application where I want to monitor the current from the output of a lamp ballast. The Ballast specs: * Output is a sine-wave (mostly sine-wave, but gets a bit distorted at higher output power) * Vout = 200-400V (peak at 1600V during ignition <250ms) * Iout = 3-10A (12A max) * Freq = 40-200kHz I believe the CR8448-2000-F is my best choose. I have a rectifying op-amp circuit to receive the output of the CT and I'm thinking of using a burd...
1 2279
by  Tony HodgesJump to last post
07/23/2013 1:07 PM
2 Replies and 2745 Views ENERGY MONITORING  2745  2 Started by  MOHUMMUD JAINOODEEN Hi, I need a circuit diagram in order to build an energy monitoring module with my CR3110-3000 current transformers.Any help or suggestion please. Thank you Mohummud
2 2745
by  MOHUMMUD JAINOODEENJump to last post
03/21/2013 1:31 AM
1 Replies and 2475 Views Wire routing  2475  1 Started by  Dan Blocker I need to route the CT leads and the 480VAC lines to a near by cabinet for power monitoring. I will be using TSP wire for the CT leads. Should I run CT leads in a seperate conduit from the 480VAC lines or will the TSP wire be enough to prevent any interference on the CT leads
1 2475
by  Tony HodgesJump to last post
03/07/2013 12:07 PM
3 Replies and 3057 Views Calculate Compressor Current by using Power and Voltage Transducer  3057  3 Started by  Ahmed Abdulbaky Please I need Your Help in this Application , we need to Measure the Current Consumed by a Compressor From single Phase , But we only have a Power Transducer (Part CR6210-250-20) and Voltage Transducer, so is it Possible To Calculate the Current From these Measurement Thanks Ahmed
3 3057
by  Tony HodgesJump to last post
12/31/2012 9:58 AM
2 Replies and 2684 Views Monitor Main entrance  2684  2 Started by  Allan Stanley I would like to monitor the AC entrance to my Barn. I have been using a product from Ubiquiti Called MFI to monitor current on a few AC motors, among other things. The Mport they sell requires a 0 to 2 volt DC input from a sensor. The sensor they have now is 100A rated and not large enough to clamp over the 400 A entrance cables. Looking for any recommendations of products found here. It's 2 lines . I would also like to have a more sensitive clamp for the neutr...
2 2684
by  Allan StanleyJump to last post
12/11/2012 6:28 PM
1 Replies and 3107 Views CR5200 - Wire Vibration  3107  1 Started by  Robert Cavagnaro Would vibration of a wire being being monitored through a CR5200 transducer affect measurement capability
1 3107
by  Tony HodgesJump to last post
08/28/2012 1:16 PM
1 Replies and 3995 Views CRD4170-5 user guide and software  3995  1 Started by  Bach Dien Hello, Please point me to where I can download user's guide and any configuration software for CRD4170-5 What protocol does it use to communicate MODBUS Thanks
1 3995
by  Tony HodgesJump to last post
10/04/2011 10:46 AM
5 Replies and 6341 Views Just need to detect run state of 3phase motor  6341  5 Started by  joe baird I need to detect the run state (on/off) of a three phase motor with a microprocessor with pins rated at 3.3v max. I have a slight preference for a digital signal but an analog signal is fine if it is 0-3.3v with some threshold meaning on. What is the simplest and most economical (I need many of these) way to do this with a CR product - a split core device would be great but I can make do with a solid core. Thanks!
5 6341
by  Tony HodgesJump to last post
12/06/2010 2:27 PM
Please register and login to participate in the forums.
Page 1 of 212 > >>


Copyright 2018 by CR Magnetics